============================== Modifying Ring Partition Power ============================== The ring partition power determines the on-disk location of data files and is selected when creating a new ring. In normal operation, it is a fixed value. This is because a different partition power results in a different on-disk location for all data files. However, increasing the partition power by 1 can be done by choosing locations that are on the same disk. As a result, we can create hard-links for both the new and old locations, avoiding data movement without impacting availability. To enable a partition power change without interrupting user access, object servers need to be aware of it in advance. Therefore a partition power change needs to be done in multiple steps. .. note:: Do not increase the partition power on account and container rings. Increasing the partition power is *only* supported for object rings. Trying to increase the part_power for account and container rings *will* result in unavailability, maybe even data loss. ------- Caveats ------- Before increasing the partition power, consider the possible drawbacks. There are a few caveats when increasing the partition power: * Almost all diskfiles in the cluster need to be relinked then cleaned up, and all partition directories need to be rehashed. This imposes significant I/O load on object servers, which may impact client requests. Consider using cgroups, ``ionice``, or even just the built-in ``--files-per-second`` rate-limiting to reduce client impact. * Object replicators and reconstructors will skip affected policies during the partition power increase. Replicators are not aware of hard-links, and would simply copy the content; this would result in heavy data movement and the worst case would be that all data is stored twice. * Due to the fact that each object will now be hard linked from two locations, many more inodes will be used temporarily - expect around twice the amount. You need to check the free inode count *before* increasing the partition power. Even after the increase is complete and extra hardlinks are cleaned up, expect increased inode usage since there will be twice as many partition and suffix directories. * Also, object auditors might read each object twice before cleanup removes the second hard link. * Due to the new inodes more memory is needed to cache them, and your object servers should have plenty of available memory to avoid running out of inode cache. Setting ``vfs_cache_pressure`` to 1 might help with that. * All nodes in the cluster *must* run at least Swift version 2.13.0 or later. Due to these caveats you should only increase the partition power if really needed, i.e. if the number of partitions per disk is extremely low and the data is distributed unevenly across disks. ----------------------------------- 1. Prepare partition power increase ----------------------------------- The swift-ring-builder is used to prepare the ring for an upcoming partition power increase. It will store a new variable ``next_part_power`` with the current partition power + 1. Object servers recognize this, and hard links to the new location will be created (or deleted) on every PUT or DELETE. This will make it possible to access newly written objects using the future partition power:: swift-ring-builder prepare_increase_partition_power swift-ring-builder write_ring Now you need to copy the updated .ring.gz to all nodes. Already existing data needs to be relinked too; therefore an operator has to run a relinker command on all object servers in this phase:: swift-object-relinker relink .. note:: Start relinking after *all* the servers re-read the modified ring files, which normally happens within 15 seconds after writing a modified ring. Also, make sure the modified rings are pushed to all nodes running object services (replicators, reconstructors and reconcilers)- they have to skip the policy during relinking. .. note:: The relinking command must run as the same user as the daemon processes (usually swift). It will create files and directories that must be manipulable by the daemon processes (server, auditor, replicator, ...). If necessary, the ``--user`` option may be used to drop privileges. Relinking might take some time; while there is no data copied or actually moved, the tool still needs to walk the whole file system and create new hard links as required. --------------------------- 2. Increase partition power --------------------------- Now that all existing data can be found using the new location, it's time to actually increase the partition power itself:: swift-ring-builder increase_partition_power swift-ring-builder write_ring Now you need to copy the updated .ring.gz again to all nodes. Object servers are now using the new, increased partition power and no longer create additional hard links. .. note:: The object servers will create additional hard links for each modified or new object, and this requires more inodes. .. note:: If you decide you don't want to increase the partition power, you should instead cancel the increase. It is not possible to revert this operation once started. To abort the partition power increase, execute the following commands, copy the updated .ring.gz files to all nodes and continue with `3. Cleanup`_ afterwards:: swift-ring-builder cancel_increase_partition_power swift-ring-builder write_ring ---------- 3. Cleanup ---------- Existing hard links in the old locations need to be removed, and a cleanup tool is provided to do this. Run the following command on each storage node:: swift-object-relinker cleanup .. note:: The cleanup must be finished within your object servers ``reclaim_age`` period (which is by default 1 week). Otherwise objects that have been overwritten between step #1 and step #2 and deleted afterwards can't be cleaned up anymore. You may want to increase your ``reclaim_age`` before or during relinking. Afterwards it is required to update the rings one last time to inform servers that all steps to increase the partition power are done, and replicators should resume their job:: swift-ring-builder finish_increase_partition_power swift-ring-builder write_ring Now you need to copy the updated .ring.gz again to all nodes. ---------- Background ---------- An existing object that is currently located on partition X will be placed either on partition 2*X or 2*X+1 after the partition power is increased. The reason for this is the Ring.get_part() method, that does a bitwise shift to the right. To avoid actual data movement to different disks or even nodes, the allocation of partitions to nodes needs to be changed. The allocation is pairwise due to the above mentioned new partition scheme. Therefore devices are allocated like this, with the partition being the index and the value being the device id:: old new part dev part dev ---- --- ---- --- 0 0 0 0 1 0 1 3 2 3 3 3 2 7 4 7 5 7 3 5 6 5 7 5 4 2 8 2 9 2 5 1 10 1 11 1 There is a helper method to compute the new path, and the following example shows the mapping between old and new location:: >>> from swift.common.utils import replace_partition_in_path >>> old='objects/16003/a38/fa0fcec07328d068e24ccbf2a62f2a38/1467658208.57179.data' >>> replace_partition_in_path('', '/sda/' + old, 14) 'objects/16003/a38/fa0fcec07328d068e24ccbf2a62f2a38/1467658208.57179.data' >>> replace_partition_in_path('', '/sda/' + old, 15) 'objects/32007/a38/fa0fcec07328d068e24ccbf2a62f2a38/1467658208.57179.data' Using the original partition power (14) it returned the same path; however after an increase to 15 it returns the new path, and the new partition is 2*X+1 in this case.