2b62f49a9d
Changed paths to avoid '..', which breaks symlinks in newer versions of sphinx. Consolidated installation include files under /_includes. Prefixed r5 versions with 'r5_' Moved files that are used up/down, but at different paths under /shared/_includes and /shared/figures Move two include files to /_includes Moved addtional images to /shared/figures/... Required for DS platform builds. Signed-off-by: Ron Stone <ronald.stone@windriver.com> Change-Id: Ia38f4205c5803b3d1fc043e6c59617c34a4e5cbd Signed-off-by: Ron Stone <ronald.stone@windriver.com>
137 lines
5.1 KiB
ReStructuredText
137 lines
5.1 KiB
ReStructuredText
|
|
.. bmj1552672912979
|
|
.. _changing-the-oam-ip-configuration-using-horizon:
|
|
|
|
=============================================
|
|
Change the OAM IP Configuration Using Horizon
|
|
=============================================
|
|
|
|
You can change the External |OAM| subnet, floating IP address, controller
|
|
addresses, and default gateway at any time after installation.
|
|
|
|
During installation, |prod| is configured with an O|AM network subnet and
|
|
related IP addresses. You can change these addresses using the Horizon Web
|
|
interface or the CLI. You can use IPv4 or IPv6 addresses.
|
|
|
|
.. caution::
|
|
Access to the |OAM| network is interrupted during this procedure. When a
|
|
swact is performed on the controllers, the newly active controller uses
|
|
the changed |OAM| IP addresses. The existing |OAM| IP addresses are no
|
|
longer valid, and you must use the new |OAM| IP addresses to reconnect to
|
|
the controller. Changes to external |OAM| access routing settings may also
|
|
be required. In addition, |VNC| console access to worker-node hosts is
|
|
interrupted until the hosts are locked and unlocked.
|
|
|
|
Once the |OAM| IP addresses are changed, any existing server certificates
|
|
\(ssl, docker\_registry, OpenStack etc.\) that have the old |OAM| IP
|
|
addresses in their |SANs| must be updated with new certificates reflecting
|
|
the new addresses.
|
|
|
|
.. rubric:: |prereq|
|
|
|
|
Before changing the |OAM| IP configuration, review the Fault Management page
|
|
and ensure that any existing system alarms are cleared.
|
|
|
|
.. rubric:: |proc|
|
|
|
|
.. _changing-the-oam-ip-configuration-using-horizon-steps-xfh-24z-5p:
|
|
|
|
#. In the |prod| Horizon, open the System Configuration page.
|
|
|
|
The System Configuration page is available
|
|
from **Admin** \> **Platform** \> **System Configuration** in the
|
|
left-hand pane.
|
|
|
|
#. Select the OAM IP tab.
|
|
|
|
The |OAM| IP page appears, showing the currently defined |OAM| network
|
|
configuration.
|
|
|
|
.. figure:: /shared/figures/system_configuration/jow1413850481192.png
|
|
:scale: 100%
|
|
|
|
#. Click **Edit OAM IP**.
|
|
|
|
The Edit OAM IP dialog box appears.
|
|
|
|
.. figure:: /shared/figures/system_configuration/jow1413850497887.png
|
|
:scale: 100%
|
|
|
|
#. Replace the IP Subnet and/or IP addresses with different ones as required.
|
|
|
|
.. note::
|
|
If you change the IP address version \(IPv4 or IPv6\), ensure that the
|
|
same version is used for the DNS servers
|
|
\(see :ref:`Specify DNS Servers Using Horizon <specifying-dns-servers-using-horizon>`\)
|
|
and NTP servers \(see :ref:`Configure NTP Servers Using Horizon <configuring-ntp-servers-and-services-using-horizon>`\).
|
|
|
|
#. Click **Save**.
|
|
|
|
This saves the configuration change and raises
|
|
**Config out-of-date** alarms on the controller and worker nodes.
|
|
|
|
#. Lock and unlock the standby controller to apply the configuration change.
|
|
|
|
|
|
#. Open the Host Inventory page, available
|
|
from **Admin** \> **Platform** \> **Host Inventory** in the left-hand
|
|
pane, and then select the **Hosts** tab.
|
|
|
|
#. In the **Hosts** list, open the drop-down menu for the standby
|
|
controller, and then click **Lock Host**.
|
|
|
|
The host is reported as locked.
|
|
|
|
#. Open the drop-down menu for the standby controller, and then
|
|
click **Unlock Host**.
|
|
|
|
#. Wait until the standby controller is reported
|
|
as **Unlocked**, **Enabled**, and **Available**.
|
|
|
|
The **Config-out-of-date alarm** for this controller is cleared.
|
|
|
|
#. Perform a swact to change the active controller.
|
|
|
|
Open the drop-down menu for the active controller, and then
|
|
click **Swact Host**.
|
|
|
|
Access to the Horizon Web interface is interrupted as control is
|
|
transferred, and Horizon becomes unresponsive. Both controllers now use
|
|
IP addresses on the new |OAM| subnet. To restore Horizon access, you must
|
|
connect the controllers physically to the new |OAM| subnet.
|
|
|
|
#. Update the system switch configurations or controller interface
|
|
connections as required to place the controller |OAM| interfaces on the
|
|
new |OAM| subnet.
|
|
|
|
#. Reconnect to Horizon using the new |OAM| floating IP address.
|
|
|
|
The former active controller is now the standby controller. It is shown
|
|
with a **Config out-of-date** alarm.
|
|
|
|
#. Lock and unlock the new standby controller to clear
|
|
the **Config out-of-date** alarm.
|
|
|
|
Wait until the standby controller is reported
|
|
as **Unlocked**, **Enabled**, and **Available**.
|
|
|
|
.. rubric:: |result|
|
|
|
|
The worker node **Config out-of-date** alarms are cleared automatically as
|
|
the system configuration is updated.
|
|
|
|
.. rubric:: |postreq|
|
|
|
|
- If alarms are not cleared after a few minutes, lock and unlock the worker
|
|
nodes to apply any other incomplete configuration changes.
|
|
|
|
- \(Optional\) If you are running Docker proxy on your system, you need to
|
|
change the **no_proxy** service parameter using the CLI to append the new
|
|
OAM IP. See, :ref:`Change the OAM IP Configuration Using the CLI <changing-the-oam-ip-configuration-using-the-cli>`.
|
|
|
|
.. seealso::
|
|
|
|
:ref:`Default Firewall Rules <security-default-firewall-rules>`
|
|
|
|
:ref:`Modify Firewall Options <security-firewall-options>`
|